Thermal Imaging
Find the Hidden Problems in Your Cold Room — Before They Find You
Most cold room problems are invisible until they're expensive. Rising power bills, recurring condensation, frost build-up, stock spoilage — these are symptoms. The actual cause is usually hidden inside your panels, behind your door frames, or in the seals you can't see. At Tundra Coldrooms, we use **professional thermal imaging cameras** to see exactly what's happening inside your cold room's structure — without pulling panels apart, without guesswork, and without unnecessary costs.
What Is Thermal Imaging?
A thermal imaging camera detects infrared radiation — essentially, heat. It creates a visual map of temperature differences across any surface, revealing hot and cold spots that are completely invisible to the naked eye. In a cold room, this is powerful. A cold room that's working properly has consistent, uniform temperatures across all surfaces. A cold room with problems has warm spots — and our camera finds every single one.
Why This Matters for Your Business
**Energy costs**
A cold room with compromised insulation uses significantly more electricity to maintain temperature. On a typical commercial cold room, insulation degradation of 25-30% can increase running costs by 15-25% annually. Over 10 years, that adds up to thousands of dollars.
**Food safety and compliance**
Temperature fluctuations caused by heat infiltration put food safety at risk. Consistent cold room performance is essential for health code compliance — and a thermal assessment gives you documented evidence that your room is performing correctly.
**Equipment life**
When a cold room's insulation fails, the refrigeration unit compensates by running longer and harder. This shortens compressor life significantly. Catching insulation problems early extends the life of your refrigeration investment.
**Avoiding unnecessary panel replacement**
Without thermal imaging, the traditional approach to a cold room problem is to replace panels and hope. With thermal imaging, we know exactly which panels — if any — need replacing. Most of the time, targeted repairs and seal replacements solve the problem at a fraction of the cost.
What We Can Find With Thermal Imaging
**Panel insulation degradation**
Cold room panels lose insulating efficiency over time as moisture penetrates the core. A panel that looks perfect on the outside may be conducting heat through a section of wet, degraded foam. Thermal imaging shows this immediately as a warm patch on an otherwise cold surface.
**Air infiltration points**
Warm air entering through door seals, panel joints, pipe penetrations and corners shows up clearly on a thermal scan. We can pinpoint exactly where air is getting in — and quantify how significant the infiltration is.
**Door seal failures**
The door is the most vulnerable point in any cold room. Thermal imaging maps the door frame in seconds, showing exactly where seals are failing and where warm air is entering on every door opening cycle.
**Refrigeration performance**
Uneven cooling, struggling evaporator coils and refrigeration units working harder than they should all have thermal signatures. We can assess whether your refrigeration is performing to spec or working overtime to compensate for insulation losses. **Condensation sources**
Condensation appears where it appears — but it comes from somewhere else. Thermal imaging traces condensation back to its actual source, so we fix the cause rather than treat the symptom.
Sunshine Coast's Cold Room Thermal Imaging Specialists
Tundra Coldrooms is based in Coolum and operates across the entire Sunshine Coast — from Noosa and Peregian to Maroochydore, Buderim, Mooloolaba and Caloundra. We're not an aircon company that does cold rooms on the side. Cold rooms are all we do — which means thermal imaging assessment is something we've invested in specifically for this work.
📞 **Call Dave: 0498 398 004**
✉️ dave@tundraconstruction.com.au
*Free, no-obligation phone consultation. We'll tell you honestly whether a thermal assessment makes sense for your situation.*
Who This Is For
- Cold rooms that are 5+ years old
- Businesses experiencing rising energy costs
- Anyone with recurring condensation or frost problems
- Cold rooms coming up for health inspection
- Anyone who's never had their room thermally assessed
Our Assessment Process
1. **Initial inspection** — we walk the room and note visible symptoms
2. **Thermal scan** — full thermal imaging of all panels, joints, door frames and ceiling
3. **Report** — we show you exactly what we've found on the thermal images
4. **Recommendation** — honest, specific advice on what needs fixing and in what order
5. **Quote** — only for work that's actually necessary
No scare tactics. No unnecessary replacements. Just a clear picture of what's going on.